DescriptionOmega Research, Inc. (ORI) is an ISO/IEC 17025 and Nadcap accredited materials testing laboratory located in Decatur, Texas. Founded in 1983, ORI provides process control testing for aerospace plating and finishing operations and serves airframe, engine, and component manufacturers throughout the industry. ORI designs, builds, and maintains a significant portion of its own test equipment.
Job Summary
ORI is seeking an experienced Facilities and Equipment Maintenance Technician on an independent contractor basis to support equipment build projects and general facility maintenance at its Decatur laboratory. The contractor will assemble and wire mechanical and electrical test equipment from drawings and work instructions, perform repairs and preventive maintenance on laboratory and facility equipment, and complete general building maintenance as assigned. The position averages approximately 20 hours per week, varies with project demand, and reports to the General Manager.
ORI provides the scope of work, materials, and acceptance criteria for each assignment. The contractor is responsible for the means, methods, and scheduling of the work within the weekly hour allocation.
Essential Duties and Responsibilities
Equipment Assembly
- Assemble bolted and welded steel structures from parts kits in accordance with ORI drawings, including fit-up, fastener torque, alignment, leveling, and anchoringInstall and route low-voltage DC instrumentation, including sensors, signal and data cables, panel-mount displays, power supplies, and circular connectors
- Terminate, solder, and strain-relieve electrical connections to documented pin-outs and verify continuity and signal output with a multimeter prior to handoffAssemble small battery-powered electronic devices and enclosures from a bill of materials and schematic
- Install and leak-check compressed gas and pneumatic lines, regulators, and fittingsWork from drawing packages, bills of materials, and written work instructions; record as-built deviations and maintain a build log for each assignment
- Turn over completed equipment to ORI personnel for verification. Calibration, operation, and release of test equipment into service are performed by ORI staff and are outside the scope of this position
Equipment Repair and Preventive Maintenance
Diagnose and repair mechanical, electrical, and pneumatic faults on laboratory and facility equipment - Perform scheduled preventive maintenance, including lubrication, filter and belt replacement, fastener inspection, and cleaningIdentify replacement parts and consumables and submit purchase requests with part numbers and justification
- Coordinate with ORI personnel before performing any work on calibrated or in-service test equipment
Facility Maintenance
Repair and adjust door hardware, closers, and weather-stripping; apply caulking and sealants as required - Mount shelving, cabinets, signage, displays, and fixtures to drywall, block, and steelPerform minor electrical repairs (outlets, lighting, cord reels), basic plumbing repairs, and drywall and paint repair
- Assist with shop organization projects, including racks, labeling, and storage installations
Physical Requirements and Work Environment
Work is performed on-site in a laboratory and light industrial environment. The contractor must be able to lift and carry up to 50 pounds, work from ladders, stand for extended periods, and work on and around powered equipment and compressed gas systems. Appropriate personal protective equipment is required. A safety and facility access orientation and a confidentiality agreement must be completed before work begins.
RequirementsRequired Qualifications
Minimum of five (5) years of hands-on experience in industrial maintenance, electro-mechanical assembly, fabrication, or a skilled trade - Ability to read and interpret mechanical drawings, wiring diagrams, schematics, and bills of materialsExperience wiring, soldering, crimping, and terminating low-voltage DC circuits and troubleshooting with a multimeter
- Experience assembling bolted and welded steel structures using torque tools, levels, and layout toolsWorking knowledge of compressed gas and pneumatic systems
- General carpentry, drywall, plumbing, and repair skillsAbility to maintain accurate written records of work performed
- Must furnish own standard hand and power tools and have reliable transportationMust be a U.S. citizen or lawful permanent resident (U.S. Person as defined in 22 CFR 120.62). This position requires access to an ITAR-controlled facility. Sponsorship is not available
- Must be able to pass a background check
Preferred Qualifications
Experience in a laboratory, aerospace, or other regulated manufacturing environment - Experience with low-voltage instrumentation, sensors, signal conditioning, and data cablingElectrical, HVAC, or similar trade license or certification
- Electronics assembly and soldering experienceBasic welding or machining capability
Familiarity with ISO 17025 or AS9100 quality systems and equipment control requirements
BenefitsCompensation and Engagement Terms
This is an independent contractor engagement. The contractor is responsible for applicable taxes and insurance and is not eligible for ORI employee benefits.
- Hourly rate of $30.00 to $45.00 depending on experience and licensureApproximately 20 hours per week on average, varying with project load
- Hours are scheduled by the contractor within normal facility hours, Monday through Friday, in coordination with the General ManagerInvoices are submitted bi-weekly with a log of hours and work completed; payment terms are net 15
- ORI provides all materials, parts, hardware, consumables, and specialty tooling required for each assignment; the contractor is expected to furnish standard hand and power tools onlyOngoing engagement, terminable at any time by either party
Omega Research, Inc. is an equal opportunity employer and engages contractors without regard to race, color, religion, sex, national origin, age, disability, or veteran status.