US
0 suggestions are available, use up and down arrow to navigate them
You’re being taken to an external site to apply.
Enter your email below to receive job recommendations for similar positions.
Electrical Engineer with Security Clearance
Parra Consulting Group Inc.
Providence, MD (Onsite)
Full-Time
CB Est Salary: $84K - $130K/Year
Parra Consulting Group, Inc. is seeking an Electrical Engineer to provide engineering support located in Aberdeen Proving Grounds, Maryland. This successful candidate will be responsible for the following:
* Assist in engineering discipline activities for conducting system, subsystem and component level, reverse engineering, replications, and validation.
* Provide hands-on RF collection, characterization, and reverse engineering of Commercial Off The Shelf (COTS) equipment and components.
* Provide hands-on technical forensic exploitation support for technical intelligence (TECHINT), media exploitation (MEDEX), cell phone exploitation (CELLEX), electronic exploitation (ELEX), and other unique exploitation missions.
* Write draft characterization reports and information tables based on requirements Qualifications Required:
* Active Top-Secret Clearance with the ability to obtain SCI.
* BA/BS in Electrical Engineering and 3 years of experience (OR) Associates degree and 6 years of experience (OR) High School and 8 years of experience
* Experience in Schematic capture and Printed Circuit Board (PCB) layout.?
* Electronic and/or RF experience with testing with related equipment.
* Understanding of RF communications, with emphasis on characterization of electronic circuits.?
* Experience using benchtop RF equipment including Signal Generators, Spectrum Analyzers, Oscilloscopes, and other equipment.?
* Perform standard RF measurements (e.g.,?occupied bandwidth, average power, pulse width) using the previously?listed test equipment.?
* Experience synthesizing and generating various types of RF waveforms using arbitrary waveform generators.? Qualifications Desired:
* * Experience in reverse engineering electronic devices from start to finish.
* Experience in reverse engineering electronic components and circuit boards.
* Experience with soldering and re-working (e.g. through-hole, surface mount, cable assemblies, wire harnesses).
* General RF or electronic domain design or test experience.
* Basic MATLAB (and other basic programming / scripting) skills should be able to apply digital processing techniques to communication signals. Techniques include digital filtering, sample rate conversion, frequency/phase estimation, demodulation, carrier recovery, timing recovery, channel equalization, pulse shaping, and forward error correction.
* Experience working with embedded systems such as Arduino and writing programs leveraging the SPI bus to configure and analyze various chipsets
* Assist in engineering discipline activities for conducting system, subsystem and component level, reverse engineering, replications, and validation.
* Provide hands-on RF collection, characterization, and reverse engineering of Commercial Off The Shelf (COTS) equipment and components.
* Provide hands-on technical forensic exploitation support for technical intelligence (TECHINT), media exploitation (MEDEX), cell phone exploitation (CELLEX), electronic exploitation (ELEX), and other unique exploitation missions.
* Write draft characterization reports and information tables based on requirements Qualifications Required:
* Active Top-Secret Clearance with the ability to obtain SCI.
* BA/BS in Electrical Engineering and 3 years of experience (OR) Associates degree and 6 years of experience (OR) High School and 8 years of experience
* Experience in Schematic capture and Printed Circuit Board (PCB) layout.?
* Electronic and/or RF experience with testing with related equipment.
* Understanding of RF communications, with emphasis on characterization of electronic circuits.?
* Experience using benchtop RF equipment including Signal Generators, Spectrum Analyzers, Oscilloscopes, and other equipment.?
* Perform standard RF measurements (e.g.,?occupied bandwidth, average power, pulse width) using the previously?listed test equipment.?
* Experience synthesizing and generating various types of RF waveforms using arbitrary waveform generators.? Qualifications Desired:
* * Experience in reverse engineering electronic devices from start to finish.
* Experience in reverse engineering electronic components and circuit boards.
* Experience with soldering and re-working (e.g. through-hole, surface mount, cable assemblies, wire harnesses).
* General RF or electronic domain design or test experience.
* Basic MATLAB (and other basic programming / scripting) skills should be able to apply digital processing techniques to communication signals. Techniques include digital filtering, sample rate conversion, frequency/phase estimation, demodulation, carrier recovery, timing recovery, channel equalization, pulse shaping, and forward error correction.
* Experience working with embedded systems such as Arduino and writing programs leveraging the SPI bus to configure and analyze various chipsets
Recommended Skills
- Assembly And Installation
- Communication
- Electrical Engineering
- Electronic Circuits
- Electronics Manufacturing
- Embedded Computer
Help us improve CareerBuilder by providing feedback about this job:
Job ID: 8340_7083654
CareerBuilder TIP
For your privacy and protection, when applying to a job online, never give your social security number to a prospective employer, provide credit card or bank account information, or perform any sort of monetary transaction. Learn more.
By applying to a job using CareerBuilder you are agreeing to comply with and be subject to the CareerBuilder Terms and Conditions for use of our website. To use our website, you must agree with the Terms and Conditions and both meet and comply with their provisions.